Grow Lights for Herbs: How to Choose the Right Light Intensity

    Understand Intensity and Daily Light Dose

    Read PPFD at Leaf Height

    PPFD is the number of photosynthetically active photons per square meter per second. This should be measured with a suitable quantum sensor at the real canopy height, including any corner of the shelf. Measuring the total photon output of a lamp does not tell you how much each pot is receiving. Make sure the sensor is level and do not block it with your body. A phone reading the brightness of a screen gives some relative values, but these are not a good substitute for accurate PPFD measurements with a suitable sensor.

    Use DLI to Compare Schedules

    While increasing the photoperiod of your herbs can boost the Daily Light Integral that they receive, it is essential to monitor their response, flowering time, maturity, and the environmental capacity of the space. When choosing a spectrum, consider it in conjunction with PPFD, photoperiod, DLI, growth stage, and space. There is no single ‘herb growing cycle’ that will fit all herbs and grow rooms. For constant artificial light, DLI = PPFD × hours × 0.0036. An example calculation for a 14-hour cycle at 200 μmol/m²/s gives about 10.1 mol/m²/day. This is an example calculation and not a target for all herbs.

    grow light (1)

    Match the Setup to the Herbs You Grow

    Basil, Thyme, and Rosemary

    The sun-loving herbs are generally required to be in a brighter position than most of the foliage houseplants. Choose compact plants with new internodes and large enough leaves that can be harvested frequently. If your basil is leaning towards the lamp, check the coverage and surrounding plants. Woody herbs also require suitable drainage, and extra light will not solve waterlogged roots. Keep similar plants together and make one change so you don’t harm more sensitive plants.

    Mint, Parsley, and Cilantro

    These herbs can work in moderate-light setups, though variety, temperature, and harvest goals affect the result. Cilantro may bolt as conditions become unsuitable; simply increasing light is not always the remedy. Keep a separate note for each species: new leaf color, stem length, soil drying, and time between harvests. Compare the same growth stage rather than judging a newly germinated tray against a mature mint pot.

    Compare Fixtures for Counters, Shelves, and Production

    Bulbs and Bars for a Small Herb Shelf

    A grow bulb can be placed in a single pot, but a grow bar spreads the light over a row of pots. Our LED grow light range provides a starting point for comparing layouts. Position bars above the full canopy and use more than one across a deep shelf if the edges remain dark. Choose adjustable mounts and a timer. Keep plugs above likely spills and avoid placing hot lamps against cabinet surfaces.

    Commercial Lights for Larger Growing Areas

    We evaluate our commercial formats for cultivation in larger spaces. Our 1500W 6 Bar full-spectrum grow light is a commercial format and not a shelf light for your kitchen. Compare installed dimensions, dimming range, and the room’s heat capacity when selecting a high-end grow light.

    Check Efficacy and Controls

    For our commercial bar-style grow lights, ANDYLED provides efficiency examples such as 3.0 micromoles per joule. Here, photon efficacy shows the useful photon output as opposed to the electrical input. These values are not guaranteed for every single model and are not used for comparison with other grow lights in a blanket fashion. Also, for a greenhouse top-lighting project, the 640W Top Fill full-spectrum grow light can be evaluated separately from the low-clearance shelf hardware.

    Set Height, Dimming, and Timing

    Find a Useful Starting Position

    Start by studying the PPFD map for your growing fixture at the height at which you will be running it and then measuring out your specific growing space. Start with the lowest output and watch for fresh growth quickly. Lowering the growing lamp will increase intensity at the center but will also increase non-uniformity, so re-measure the corners after each move. A 12–16 hour day with a daily dark period is a good starting point for most indoor herb growers and must also take into account any natural light from a window and the specific growing plants’ response to that light.

    Commission a Larger Herb Rack

    Testing for low light output, flicker, unexpected dimming down to minimum or blacking out of entire sections, as well as consistency from fixture to fixture, is typical for acceptance testing of commercial dimming systems. Additional testing of dimming system control, such as scheduling, group commands, loss of communication, and recovery after power cycling, is also typical. Measuring canopy PPFD, edge PPFD, and overall uniformity at specified dimmed light levels, as opposed to only measuring at full light, is typical, as opposed to acceptance testing that only measures at full light. Note that not all models have gone through this testing.

    Keep Spectrum Balanced

    Full-spectrum light makes good sense for leafy crops and is far better for inspecting leaves under growth than strong color. While blue light can help to compact growth, color is never a substitute for adequate intensity. The grow light spectrum guide explains why useful coverage and a balanced mix are essential – don’t buy a grow light simply because it has a blue or purple appearance.

    240W-2x2ft-Detachable-LED-Grow-Light-AD4-240W-D31-054-2

    Adjust From Plant Response and Running Cost

    Treat Heat and Water as Part of Lighting

    Commercial growing systems integrate light with air and humidity management using aluminum frames that distribute heat but do not keep a constant temperature. After an output change, check canopy temperature, grow room temperature, airflow, humidity, and irrigation response. There is no single prescription for watering in this principle.

    Troubleshoot Before Raising Power

    While stretched stems may indicate insufficient light and pale upper leaves indicate excessive light, other factors such as pests, root damage, and lack of nutrients can produce similar symptoms. So change one thing and see the effects on the next flush of leaves. Pinch the basil plant to make it branch more. Keep the pots far enough apart for the leaves not to touch and overshadow each other. Don’t solve a watering problem by turning up the dimmer – read the indoor plant lighting guide for some general criteria to use when choosing lights.

    After harvest, the light geometry changes. Cut back the entire basil plant, and the leaves that remain will be farther away from the light than before. Check the newly exposed canopy before you increase the time the lamp is on or raise the power.

    For testing intensity changes, keep your observation group small and compare to a similar set of plants being grown under the previous intensity using similar pots and watering. Compare the new growth of cut tops to each of the altered intensity settings rather than assuming more light automatically equals more harvest.

    Taller plants such as rosemary and basil should be placed near the end of a fixture to allow for adequate clearance. Short parsley plants can be placed on short risers to maximize space on the shelf. Be sure to leave enough space so that moving a plant in the back will not affect the light that other plants are receiving.

    Calculate the Monthly Bill

    For an 80w light running 14 hours a day, this is 1.12kWh per day or 33.6kWh over 30 days. Adding a timer or making use of natural daylight can help offset this, as well as minimizing the space you need to grow in. Even with high-efficacy lights, a lot of the photons will be wasted if they are not hitting the plants. Readings will also change after a big harvest when the plants drop down in height.

    FAQ

    Q: How intense should grow lights for herbs be?

    A: Follow species-specific guidelines and use actual measured canopy PPFD. Compact new growth up and harvest frequently enough to get good performance rather than using the same wattage for all herbs.

    Q: How long should herb grow lights stay on?

    A: Start with a 12–16 hour light/dark cycle for an indoor setup. Keep darkness as constant as possible and adjust for natural daylight and crop response.

    Q: How close should a grow light be to basil?

    A: Follow the PPFD map, measure the leaves, and adjust the distance or dimming. There is no one-size-fits-all distance to set for all fixture types.

    Q: Why is cilantro bolting under grow lights?

    A: Temperature, crop maturity, variety, and day length affect this. Review these factors rather than automatically increasing production.